Betaflight Blackbox and debug: CLI settings

Blackbox logging device, sample rate and which fields are logged, plus `debug_mode`, which picks what the four debug channels record.

20 settings in Betaflight 2026.6. Each range and value list is read from the firmware's settings.c, each default from the CLI get of the release built for the simulator (no board config applied), so a board's own config can still change it. Set one with set name = value, then save. Paste a diff all into the CLI checker to test it against any release.

Setting	Type	Range or values	Default	4.4	4.5	2025.12	2026.6	Notes
`blackbox_device` #	uint8 global	NONE, SPIFLASH, SDCARD, SERIAL, VIRTUAL	`NONE` needs USE_BLACKBOX	✓	✓	Δ	✓	2025.12: new values VIRTUAL
`blackbox_disable_acc` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX, USE_ACC	✓	✓	✓	✓
`blackbox_disable_alt` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX, USE_BARO, USE_RANGEFINDER	✓	✓	✓	✓
`blackbox_disable_attitude` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX, USE_ACC	—	—	✓	✓
`blackbox_disable_bat` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_disable_debug` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_disable_gps` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX, USE_GPS	✓	✓	✓	✓
`blackbox_disable_gyro` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_disable_gyrounfilt` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	—	✓	✓	✓
`blackbox_disable_mag` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX, USE_MAG	✓	✓	✓	✓
`blackbox_disable_motors` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_disable_pids` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_disable_rc` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_disable_rssi` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_disable_servos` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX, USE_SERVOS	—	—	✓	✓
`blackbox_disable_setpoint` #	uint32 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_high_resolution` #	uint8 global	OFF, ON	`OFF` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_mode` #	uint8 global	NORMAL, MOTOR_TEST, ALWAYS	`NORMAL` needs USE_BLACKBOX	✓	✓	✓	✓
`blackbox_sample_rate` #	uint8 global	1/1, 1/2, 1/4, 1/8, 1/16	`1/4` needs USE_BLACKBOX	✓	✓	✓	✓
`debug_mode` #	uint8 global	101 values NONE, CYCLETIME, BATTERY, GYRO_FILTERED, ACCELEROMETER, PIDLOOP, RC_INTERPOLATION, ANGLERATE, ESC_SENSOR, SCHEDULER, STACK, ESC_SENSOR_RPM, ESC_SENSOR_TMP, ALTITUDE, FFT, FFT_TIME, FFT_FREQ, RX_FRSKY_SPI, RX_SFHSS_SPI, GYRO_RAW, MULTI_GYRO_RAW, MULTI_GYRO_DIFF, MAX7456_SIGNAL, MAX7456_SPICLOCK, SBUS, FPORT, RANGEFINDER, RANGEFINDER_QUALITY, OPTICALFLOW, LIDAR_TF, ADC_INTERNAL, RUNAWAY_TAKEOFF, SDIO, CURRENT_SENSOR, USB, SMARTAUDIO, RTH, ITERM_RELAX, ACRO_TRAINER, RC_SMOOTHING, RX_SIGNAL_LOSS, RC_SMOOTHING_RATE, ANTI_GRAVITY, DYN_LPF, RX_SPEKTRUM_SPI, DSHOT_RPM_TELEMETRY, RPM_FILTER, D_MAX, AC_CORRECTION, AC_ERROR, MULTI_GYRO_SCALED, DSHOT_RPM_ERRORS, CRSF_LINK_STATISTICS_UPLINK, CRSF_LINK_STATISTICS_PWR, CRSF_LINK_STATISTICS_DOWN, BARO, AUTOPILOT_ALTITUDE, DYN_IDLE, FEEDFORWARD_LIMIT, FEEDFORWARD, BLACKBOX_OUTPUT, GYRO_SAMPLE, RX_TIMING, D_LPF, VTX_TRAMP, GHST, GHST_MSP, SCHEDULER_DETERMINISM, TIMING_ACCURACY, RX_EXPRESSLRS_SPI, RX_EXPRESSLRS_PHASELOCK, RX_STATE_TIME, GPS_RESCUE_VELOCITY, GPS_RESCUE_HEADING, GPS_RESCUE_TRACKING, GPS_CONNECTION, ATTITUDE, VTX_MSP, GPS_DOP, FAILSAFE, GYRO_CALIBRATION, ANGLE_MODE, ANGLE_TARGET, CURRENT_ANGLE, DSHOT_TELEMETRY_COUNTS, RPM_LIMIT, RC_STATS, MAG_CALIB, MAG_TASK_RATE, EZLANDING, TPA, S_TERM, SPA, TASK, GIMBAL, WING_SETPOINT, CHIRP, FLASH_TEST_PRBS, MAVLINK_TELEMETRY, AUTOPILOT_PID, AUTOPILOT_STOP	`NONE`	✓	Δ	Δ	Δ	4.5: new values GPS_CONNECTION, GYRO_CALIBRATION, ANGLE_MODE, ANGLE_TARGET, CURRENT_ANGLE, RPM_LIMIT, RC_STATS, MAG_CALIB, MAG_TASK_RATE, EZLANDING 2025.12: new values MULTI_GYRO_RAW, MULTI_GYRO_DIFF, OPTICALFLOW, D_MAX, MULTI_GYRO_SCALED, AUTOPILOT_ALTITUDE, TPA, S_TERM, SPA, TASK, GIMBAL, WING_SETPOINT, AUTOPILOT_POSITION, CHIRP, FLASH_TEST_PRBS, MAVLINK_TELEMETRY; values dropped GYRO_SCALED, DUAL_GYRO_RAW, DUAL_GYRO_DIFF, D_MIN, DUAL_GYRO_SCALED, GPS_RESCUE_THROTTLE_PID 2026.6: new values AUTOPILOT_PID, AUTOPILOT_STOP; values dropped AUTOPILOT_POSITION

✓ present, Δ changed in that release (hover for what changed), — not in that release. “needs USE_…” is the build option the setting is compiled with: a cloud build without it has no such setting.

Also in this section

These settings exist in 2026.6, but their default depends on build options the simulator build does not compile (DShot, RPM filter, board drivers), so it is not printed here rather than guessed: blackbox_disable_rpm.

Other sections

Gyro and D-term filters (27)
PID tuning (73)
Angle, horizon and launch modes (20)
Rates and throttle curve (25)
Motors and ESC (23)
Receiver and RC link (32)
Failsafe and arming (14)
GPS (14)
GPS rescue (12)
Autopilot, position and altitude hold (66)
Battery and current sensor (28)
OSD (49)
OSD element positions (90)
VTX and camera control (12)
Telemetry and serial (44)
LED strip and beeper (12)
Sensors and board alignment (35)
System and hardware (25)

What changed between releases: 4.4 → 4.5 · 4.5 → 2025.12 · 2025.12 → 2026.6. Machine-readable: params.json (2026.6.2), GPL-3.0 like the firmware it comes from.